Updated November 2026
To put AirPods in pairing mode, you open the lid of the charging case and hold the setup button on the back until the status light flashes white. Once that light is flashing, the earbuds are discoverable and your phone, laptop or tablet can find them in its Bluetooth list. The exact button and light behavior depends on your model, so the steps below cover each generation.
Before You Start
Pairing mode only works when the earbuds have enough charge and are not already connected to another device. Check these points first so you do not spend time chasing a problem that is really a battery or connection issue.
Shopping for one? See our guide: AirPods Pro 3 Case Review: Features, Pros and Cons.
- Charge the case for at least 15 minutes, or keep it plugged in while you work.
- Turn Bluetooth on in the device you want to pair with.
- Disconnect the AirPods from any other phone or laptop that is nearby and signed in to the same Apple ID.
- Keep the earbuds and the device within a few feet of each other.
How to Enter Pairing Mode on AirPods, AirPods Pro, and AirPods 3
Most AirPods with a charging case use the same basic method. The setup button sits on the back of the case, below the lid hinge on the lightning-port models and on the back face of the case on newer ones.
- Place both earbuds in the case and close the lid.
- Open the lid and keep it open. The earbuds should remain inside.
- Press and hold the setup button on the back of the case until the status light flashes white.
- Look for the AirPods name on your device’s Bluetooth screen and tap Connect.
On some models the light flashes amber first, then white. Amber usually means the earbuds need more charge or are not fully seated. Keep holding the button until you see white.
How to Enter Pairing Mode on AirPods Max and AirPods Pro 3
The over-ear AirPods Max use a different control. Instead of a case button, you press and hold the Digital Crown and the noise control button together. Hold them until the status light begins to flash white, then select the headphones on your device.
AirPods Pro 3 follow the case-button method described above, but the light behavior can differ slightly from earlier Pro models. If the light does not change after a few seconds, check the setup page for your model on Apple’s support site.
Pairing AirPods With Android or a Windows Laptop
Android phones and Windows PCs do not use the iPhone’s pop-up card, so you need to start the pairing from the Bluetooth menu. Open the Bluetooth settings on the device, make sure scanning is on, and put the AirPods into pairing mode as described above. When “AirPods” appears in the list, select it. Android may show the device as a generic Bluetooth headset until the first connection finishes.
Troubleshooting when the name does not appear
- Close the lid, wait 10 seconds, then open it and hold the button again.
- Forget the AirPods on all devices and restart Bluetooth on the target device.
- Restart the phone or laptop if the list stays empty.
Common Mistakes
- Holding the button too briefly. You need to hold it for several seconds until the light changes.
- Closing the lid too soon. Keep the lid open during pairing, or the status light will not show.
- Pairing with a device still linked to the same Apple ID. Your iPhone may take over the connection automatically.
- Ignoring low battery. A weak case can cause the light to flicker or fail to flash.
FAQ
Why won’t my AirPods show up in the Bluetooth list?
The earbuds are usually still connected to another device or are not in pairing mode. Reset the setup by holding the case button after the earbuds are removed from the case, then try again.
What does a flashing amber light mean?
Amber typically means low battery or a fault in the earbuds. Charge the case, reseat the earbuds, and hold the setup button again until you see white.
Do I need to re-enter pairing mode for each new device?
Yes. Each new phone, tablet, or computer needs its own pairing session, though iPhones and iPads signed in to the same Apple ID often connect automatically.
Conclusion
Pairing mode is the same basic process across most AirPods: open the lid, hold the setup button until the light flashes white, and select the earbuds on your device. AirPods Max use the Digital Crown and noise control buttons instead. If the connection still fails, a full reset and a charged case usually solve it.
Related reading
- AirPods Pro 3 Pairing Mode: How to Put Them in Pairing Mode
- How to Put AirPods in Pair Mode: 3 Steps for Every Model
- How to Connect AirPods Max to iPhone: Step-by-Step Pairing Guide
- Where to Get the Right AirPods Pro Replacement and How to Pick It
- When Do AirPods Come Out? Release Dates and How to Tell
- Only One AirPods Is Working? How to Fix It in 7 Steps

