Updated November 2026

To put AirPods Pro 3 in pairing mode, open the lid of the charging case with the earbuds inside, then press and hold the button on the back of the case until the status light flashes white. Once the light pulses, your AirPods Pro 3 are discoverable and ready to pair with a new iPhone, iPad, Mac, Android phone, or other Bluetooth device. The whole process usually takes less than 30 seconds.

Before You Start

Pairing mode only works when the earbuds and case have enough charge to run the connection. Check the battery first, because a low case can cause the light to behave unpredictably. Also make sure the earbuds are inside the case and the lid is open, since closing the lid or removing the buds will reset the pairing state.

Shopping for one? See our guide: AirPods Pro 3 Case Review: Features, Pros and Cons.

  • Confirm the case has at least some charge, ideally above 20 percent.
  • Keep the earbuds seated in their slots, not resting on top of the case.
  • Turn off Bluetooth on the old device if you want the AirPods to connect to a new one.

Step-by-Step: Entering Pairing Mode

  1. Open the case lid with both earbuds inside. Leave it open.
  2. Locate the button on the back of the case, just below the lid hinge.
  3. Press and hold the button for about 3 to 5 seconds. Keep holding until the status light between the earbuds flashes white.

What the Status Light Means

A white flashing light means the AirPods are discoverable. A solid amber light usually means the case battery is low or the buds are still charging, not that pairing is active. If you see amber, connect the case to power for a few minutes and try the steps again.

Connecting Your Device

Once the light flashes white, go to your device’s Bluetooth settings. On an iPhone, the AirPods typically appear as a pop-up card near the top of the screen. On an Android phone or Windows PC, open Bluetooth settings, choose Pair new device, and select AirPods Pro from the list. Pairing finishes in a few seconds, and the light turns solid green once the connection is ready.

Troubleshooting When Pairing Mode Doesn’t Start

If the light never flashes white, the most common causes are a dead case or a stuck button press. Try a different charging cable and wall adapter, then repeat the hold. A hard reset also helps: with the case closed for 30 seconds, open it, hold the button for about 15 seconds until the light flashes amber then white, and try pairing again. If the problem continues, Apple’s support site lists additional diagnostics. Consult an authorized Apple service provider before attempting repairs that involve opening the case.

Common Mistakes

  • Closing the lid too early, which can end pairing mode before your device sees the buds.
  • Holding the button on the earbuds instead of the case. The case button is the one that starts pairing.
  • Trying to pair while the old device is still connected, which can make it appear the AirPods are missing.
  • Confusing solid amber with pairing mode. Amber signals charging or low battery.
  • A short, reliable USB-C cable helps keep the case charged so the pairing light behaves predictably. View on Amazon
  • A wireless charging pad rated for Qi devices lets you top up the case quickly before pairing. View on Amazon

FAQ

Can I pair AirPods Pro 3 with an Android phone?

Yes. Put the AirPods in pairing mode, then open Bluetooth settings on your Android device and select AirPods Pro from the list of available devices.

Amber usually means the case or earbuds need charging. Connect the case to power for several minutes, then hold the button again.

Do I need to reset my AirPods Pro 3 to enter pairing mode?

No, a reset is only needed if pairing mode fails repeatedly. For a normal new connection, simply holding the case button with the lid open is enough.

Conclusion

Open the case with the earbuds inside, hold the back button until the light flashes white, then choose your AirPods from your device’s Bluetooth list. Check the battery and charging light first if the process doesn’t start. Once paired, your AirPods Pro 3 will reconnect automatically to devices signed into the same Apple account.

Owen Palmer

About Owen Palmer

Owen Palmer is part of our editorial team and reviews and edits our brand headphones & noise cancelling guides, checking product details against manufacturer specifications and owner feedback.