Updated November 2026
To turn on noise cancelling on Bose headphones, you usually press a dedicated button or use the Bose Music app, depending on your model. Most current Bose noise cancelling headphones let you switch between full noise cancelling, a lighter Aware or Quiet Mode, and off. This guide walks through the common methods, explains how to tell that ANC is active, and covers the fixes to try when it won’t turn on.
Step-by-Step: Turning On Noise Cancelling
The exact control depends on your headphone generation, but the process follows a consistent pattern.
Shopping for one? See our guide: 6 Best Bose Headphones Noise Cancellings for Every Need (2026).
- Power on the headphones. Press and hold the power button until you hear the startup tone or see the status light.
- Locate the noise cancelling control. On many over-ear models, this is a dedicated button on the right earcup, often labeled with an ANC or noise cancelling icon. On some earbud models, you press or hold the stem or touch surface.
- Press the button once. You should hear a voice prompt or tone confirming the mode change, such as “Noise cancelling on.”
- Confirm the mode in the Bose app if your model supports it. Open the app, select your headphones, and check the listening mode setting.
Using the Bose Music App to Switch Modes
If your headphones have no dedicated button, or you want finer control, the Bose Music app is the most reliable route. Bose lists its noise cancelling and listening mode options in the app, and changes made there apply immediately. Pair your headphones with your phone first, then open the app and look for the listening mode or noise control section.
Manufacturers note that some modes are available only on specific models and firmware versions. If you don’t see an ANC option, check for a firmware update before assuming a fault.
How to Tell Noise Cancelling Is Working
Noise cancelling is generally easy to confirm by ear. The most useful checks are:
- A voice prompt or tone announcing the mode change.
- A noticeable drop in steady sounds like HVAC hum, road noise or engine drone.
- An indicator light or app status showing the active mode.
Keep in mind that noise cancelling reduces low-frequency, constant sounds most effectively. Sudden voices and sharp noises will still come through, so a quiet result for those is normal.
Troubleshooting When ANC Won’t Turn On
If the mode doesn’t engage, work through these checks in order:
- Charge the headphones for at least 15 minutes, since low battery can limit features.
- Restart the headphones by holding the power button until they shut off, then turn them back on.
- Unpair and re-pair the headphones with your phone.
- Update the firmware through the Bose Music app.
- Reset the headphones following the reset steps in Bose’s support documentation for your model.
Owners often report that a firmware update resolves most mode-switching problems that appear suddenly after a phone update.
Common Mistakes
- Pressing the button too quickly. A single, firm press is usually enough; repeated presses can cycle through modes unintentionally.
- Confusing Aware or Quiet Mode with full noise cancelling. These are separate settings, and one may be active when you expect the other.
- Leaving the app out of the process. Some changes only confirm correctly when the app is connected.
- Ignoring a poor seal. A loose fit reduces ANC effectiveness, so adjust the earcups or ear tips.
Recommended Gear
- Bose headphone carrying case: A hard case protects the earcups and cable during travel, which helps keep the ANC microphones and hardware undamaged. View on Amazon
- Replacement ear cushions: Fresh cushions restore a proper seal, which directly affects how well noise cancelling performs. View on Amazon
FAQ
Why don’t I hear a voice prompt when I turn on noise cancelling?
Voice prompts can be turned off in the Bose Music app or may be muted by your phone’s volume settings. Check the app’s settings for prompt options first.
Can I use noise cancelling without the Bose app?
On many models, yes. A dedicated button or touch control handles basic switching, while the app adds finer options and firmware updates.
Does noise cancelling drain the battery faster?
Yes, ANC uses extra power because it runs microphones and processing continuously. Manufacturers specify battery life for both ANC on and off, so check your model’s documentation for the exact figures.
Conclusion
Turning on noise cancelling on Bose headphones usually takes one press of a dedicated button or a quick change in the Bose Music app. If the mode won’t engage, charge the headphones, restart them, and update the firmware before trying a full reset. Check your model’s manual for the exact controls, since layouts differ between generations.
Related reading
- Sony Versus Bose Noise Cancelling Headphones: Which Fits You Best (2026)
- How to Turn on Bose Quiet Comfort Headphones: A Practical Guide (2026)
- How to Turn On Bose QuietComfort Headphones: 3 Quick Steps (2026)
- How to Turn On Bose QC Headphones: A Step-by-Step Guide (2026)
- How to Turn On Bose Headphones: A Step-by-Step Guide for Beginners
- How to Turn Off Bose QuietComfort Headphones: 4 Quick Methods That Work (2026)

