Updated November 2026

To turn on noise cancellation on AirPods 4, you can use the stem press, Control Center on your iPhone, or the Settings app. This guide walks through each method, explains which one to use in different situations, and covers what to check if the feature doesn’t switch on. The steps apply to the AirPods 4 with Active Noise Cancellation, which is the model Apple sells with the noise-cancelling feature built in.

Turn It On Using the Stem Press

The fastest way to change listening modes is by pressing the stem. Apple’s default setting cycles through the modes when you press it, so you can switch without touching your phone.

Shopping for one? See our guide: 3 Best Apple AirPods 4 Noise Cancellation Options Compared (2026).

  1. Put both AirPods 4 in your ears and make sure they are connected to your iPhone or other Apple device.
  2. Press and hold the stem of either AirPod for about one second, or until you hear a tone.
  3. Repeat the press to cycle through the modes until you reach Noise Cancellation.
  4. Listen for the change. Outside sound should drop noticeably, especially low, steady sounds like engine hum or air conditioning.

If your stem press opens Siri instead, the stem controls are set to a different action. You can change this in Settings, which is covered below.

Turn It On from Control Center on iPhone

Control Center lets you switch modes without relying on the stem, which helps if you are wearing gloves or if your earbuds are not seated well enough to press comfortably.

  1. Open Control Center. On iPhone with Face ID, swipe down from the top-right corner. On other models, swipe up from the bottom edge.
  2. Press and hold the volume slider, or the audio card in the top-right area, until the expanded controls appear.
  3. Tap the Noise Control button, which shows a circle icon.
  4. Select Noise Cancellation from the list of modes.

Turn It On from the Settings App

The Settings app gives you the most control, including the option to change what the stem press does. Use this method if you want Noise Cancellation to be the default mode each time you use the AirPods.

  1. Open Settings and tap Bluetooth.
  2. Tap the information icon next to your AirPods 4.
  3. Under Noise Control, choose Noise Cancellation.
  4. To change what the stem press does, go to the Press and Hold AirPods section and select the Noise Control option for the press action.

What to Check If It Won’t Turn On

If the mode doesn’t change, the cause is usually a setting, a connection issue, or a firmware problem. Work through these checks in order.

  • Confirm the AirPods are the Active Noise Cancellation model. Apple’s standard AirPods 4 without the noise-cancelling feature do not offer this mode.
  • Make sure the stem press is assigned to Noise Control, not Siri or Playback.
  • Check that both AirPods are seated properly. Noise Cancellation relies on both earbuds forming a seal.
  • Update your iPhone to the latest iOS version, since firmware and Bluetooth fixes are delivered through system updates.
  • Reset the AirPods if the problem persists by holding the setup button on the case until the light flashes amber and then white, then reconnecting.

Common Mistakes to Avoid

  • Pressing the stem too briefly. A short tap may trigger playback instead of mode switching, so hold for about a second.
  • Assuming Noise Cancellation is off because you feel no change. A poor ear fit reduces the effect, so try a different tip size if your AirPods feel loose.
  • Forgetting that Transparency mode is a separate option. If you can hear people speaking clearly, you may be in Transparency rather than Noise Cancellation.
  • Leaving the AirPods connected to an older device that doesn’t support the mode, which can limit which controls appear.
  • A soft zippered case keeps the AirPods 4 protected from scratches and pressure when you carry them in a bag, which helps the earbud fit stay consistent over time. View on Amazon
  • A pair of replacement silicone ear tips can help you get a proper seal, which matters because Noise Cancellation depends on a snug fit. View on Amazon

FAQ

Can I turn on noise cancellation without my iPhone?

The stem press works with the AirPods connected to any compatible Apple device, but the setting is stored on the device they are paired with. Changing the mode from an iPhone is the most reliable option.

Why does Noise Cancellation feel weaker than expected?

Fit is the most common reason. If the earbuds don’t sit securely in your ear, low-frequency sound will still get through, so check your ear tip size and reseat the AirPods.

Is Noise Cancellation the same as Transparency mode?

No. Noise Cancellation reduces outside sound, while Transparency lets surrounding sound through so you can hear people and announcements. You can switch between them using the same controls.

Conclusion

You can turn on noise cancellation on AirPods 4 using the stem press, Control Center, or the Settings app, and each method takes only a few seconds. If the mode won’t activate, check the model, the stem assignment, and your fit before resetting. Once it is set as your default, you won’t need to switch it again.

Emily Parker

About Emily Parker

Emily Parker is part of our editorial team and reviews and edits our brand headphones & noise cancelling guides, checking product details against manufacturer specifications and owner feedback.