Updated November 2026

To factory reset Bose QuietComfort headphones, you power the unit off, then hold the power and Bluetooth buttons together until the status light flashes. This clears saved Bluetooth pairings, resets the noise cancelling and EQ settings, and often fixes stubborn connection or audio problems. The exact button combination differs slightly between QuietComfort models, so check the steps below against your headset.

Before You Start

A reset erases every paired device stored on the headphones, so you will need to pair them again afterward. Charge the headphones to at least half before you begin, since a reset interrupted by a dead battery can leave them in an odd state. Keep your phone or laptop nearby with Bluetooth turned on.

Shopping for one? See our guide: 5 Best Bose QuietComfort Headphones Case Options for Travel (2026).

How to Factory Reset QuietComfort Models

  1. Turn the headphones off completely. Slide the power switch or press and hold the power button until the voice prompt says the unit is powering off.
  2. Press and hold the power button and the Bluetooth button at the same time. On most QuietComfort models, the Bluetooth button is the one with the Bluetooth symbol on the right earcup.
  3. Keep both buttons held for about 10 seconds. The status light will flash, and you may hear a voice prompt confirming the reset.
  4. Release the buttons, then power the headphones back on. Your earlier pairings should be gone, so the headphones will enter pairing mode on their own or you will need to start pairing manually.

Confirming the Reset Worked

After the reset, the headphones should no longer appear as connected on any device you used before. If an old phone still lists them, forget the device in that phone’s Bluetooth settings, because a stale entry can block a clean reconnection.

Pair the Headphones Again

Once the reset is complete, put the headphones in pairing mode and reconnect them to your device. Owners often report that the first pairing after a reset succeeds more reliably if the headphones are close to the device and no other Bluetooth accessories are nearby. For a full walkthrough, see How to Pair Bose Headphones: A Step-by-Step Guide for Beginners.

When a Reset Helps and When It Does Not

A factory reset is most useful when the headphones keep dropping connections, refuse to pair with a device they used before, or behave oddly after a firmware change. It will not fix physical damage, a worn battery, or a unit that no longer charges. If the headphones still misbehave after a reset, the next step is to check the warranty. Warranty for Bose Headphones: How to Check, Claim and Protect Yours explains what coverage may apply.

Problem Does a reset usually help?
Won’t reconnect to a previously paired phone Yes, in most cases
Noise cancelling or EQ behaves strangely Often
Battery drains quickly Rarely, since this points to battery wear
Physical damage or no charging No

Common Mistakes

  • Pressing the buttons while the headphones are still on. Power them fully off first.
  • Releasing the buttons too early. Hold them for the full 10 seconds so the reset completes.
  • Forgetting to remove the headphones from old devices. Stale pairings can block reconnection.
  • Assuming the reset fixes a dead battery. Charge the unit and test it before blaming software.
  • Skipping the manual for your exact model. Button layouts vary slightly between QuietComfort generations.
  • A soft carrying case helps protect the earcups and controls from pressure while the headphones are stored between uses. View on Amazon
  • A short USB-C charging cable keeps the battery topped up before a reset so the process is not interrupted. View on Amazon

FAQ

Does a factory reset delete my music or files?

No. Bose headphones store no music, so a reset only clears Bluetooth pairings and saved settings. Your audio files stay on your phone or computer.

How do I know the reset finished?

The status light flashes and a voice prompt usually confirms the reset. If you hear nothing, repeat the steps and hold the buttons for the full 10 seconds.

Will a reset fix a headset that will not turn on?

Usually not. A reset needs the headphones to power on first, so if they stay dead, charge them for at least 30 minutes and try again. If they still will not start, contact Bose support.

Conclusion

A factory reset clears old pairings and resets settings, which resolves many connection problems on Bose QuietComfort headphones. Power the unit off, hold the power and Bluetooth buttons for about 10 seconds, then pair again from scratch. If the problem remains, your model’s manual or Bose support is the next place to check.

Owen Palmer

About Owen Palmer

Owen Palmer is part of our editorial team and reviews and edits our brand headphones & noise cancelling guides, checking product details against manufacturer specifications and owner feedback.