Updated November 2026

To turn on Bose QuietComfort headphones, press and hold the power button for about one second until you hear a voice prompt or tone. Most QuietComfort models use the same basic method, though the exact button location differs slightly between generations. This guide walks through the steps and what to check if the headphones won’t power up.

Step 1: Charge the Headphones if Needed

Before anything else, make sure the battery has enough charge. Connect the headphones to a USB-C cable and a power source. Bose generally lists a few hours of charging for a full charge, and a short charge will still give you enough power to turn on and confirm the unit responds. If the headphones show no response at all after 15 to 20 minutes on the charger, move on to the troubleshooting section below.

Shopping for one? See our guide: 5 Best Bose QuietComfort Headphones Case Options for Travel (2026).

Step 2: Locate the Power Button

On most QuietComfort models, the power button sits on the right earcup, often near the USB-C port or on the outer edge. On QuietComfort Ultra models, the controls sit on the right earcup as a touch surface and a button. Check your model’s manual or the Bose app if you can’t find it quickly.

Step 3: Press and Hold to Power On

  1. Press and hold the power button for about one second.
  2. Wait for a voice prompt, tone, or LED indicator. The voice prompt typically announces the battery level.
  3. Confirm the headphones connect to your device. If they don’t, open Bluetooth settings on your phone or laptop and select the Bose headphones.

How to Confirm the Headphones Are On

Manufacturers specify a small set of cues to check. A voice prompt or tone means the unit has powered on. An LED light, where your model has one, changes color or blinks to show status. If you hear nothing and see no light, the battery may be fully drained or the unit may need a reset.

What you notice What it usually means
Voice prompt or tone Headphones are on and ready to pair
LED blinking Headphones are powering on or in pairing mode
No sound, no light Battery is empty or the unit needs charging

Troubleshooting When the Headphones Won’t Turn On

If the headphones stay silent after a full charge, try a reset. Owners often report that a reset clears the issue, and the exact steps depend on your model. Check the Bose support site for the reset procedure matching your headphones. Also confirm the USB-C cable and power adapter work with another device. A damaged cable is a common cause of charging problems.

Common Mistakes

  • Holding the power button too briefly, which may not register as a power command.
  • Assuming the headphones are off when they are simply out of Bluetooth range from your device.
  • Using a low-output or damaged USB-C cable, which can slow or stop charging.
  • Confusing the pairing button with the power button on some models.
  • Leaving the headphones on the charger for long periods without checking the battery indicator.
  • Replacement USB-C charging cable: A spare cable helps you rule out a faulty one when the headphones won’t charge. View on Amazon
  • Carrying case: A hard case protects the earcups and controls, which keeps the power button and touch surfaces in good shape. View on Amazon

FAQ

Do Bose QuietComfort headphones turn on automatically when I put them on?

On most models they do not. You need to press the power button, although some models wake from a sleep state when you touch the controls. Check your manual for the exact behavior.

What if my Bose headphones turn on but won’t connect?

Turn off Bluetooth on your device, then turn it back on and select the headphones from the list. If that fails, put the headphones into pairing mode and try again. Bose’s support pages include pairing steps for each model.

How long does the battery last after I turn them on?

Bose specifies battery life in hours of playback with noise cancelling on, and the figure varies by model. Battery life also drops as the battery ages, so check the Bose app for a current battery reading.

Conclusion

To turn on Bose QuietComfort headphones, charge them if needed, press and hold the power button for about one second, then wait for the voice prompt or tone. If nothing happens, check the cable, try a reset, and confirm the battery has charge. For pairing and setup steps after the headphones are on, see the related guides on this site.

Owen Palmer

About Owen Palmer

Owen Palmer is part of our editorial team and reviews and edits our brand headphones & noise cancelling guides, checking product details against manufacturer specifications and owner feedback.